Siemens Simatic ET 200SP Digital Input Module DI 16X24V DC ST 6ES71316BH010BA0
Product Description
-
A digital input module is a component used in industrial automation systems to interface with digital signals
-
It converts binary signals (on/off, high/low) from field devices,such as sensors or switches,into data that a programmable logic controller (PLC) or other control systems can process
-
This module allows the control system to monitor and respond to the status of various equipment and processes in real-time
-
Warranty and support will be provided by vendor
-
Note:*Actual product image may vary from that shown on the picture
Product Specification
| Brand | Siemens |
| Product Type | Digital Input Module |
| Product Code | 6ES71316BH010BA0 |
| Product Series | Simatic ET 200SP |
| Product Type Designation | DI 16x24VDC ST |
| HW Functional Status | From FS02 |
| Firmware Version | V0.0 |
| Usable Base Units | BU type A0 |
| Product Function | |
| I&M Data | Yes; I&M0 to I&M3 |
| Isochronous Mode | No |
| Engineering With | |
| Step 7 TIA Portal Configurable/Integrated From Version | V14 |
| Step 7 Configurable/Integrated From Version | V5.5 SP3 |
| PCS 7 configurable/integrated from version | V8.1 SP1 |
| Profibus from GSD version/GSD revision | One GSD file each, Revision 3 and 5 and higher |
| Profinet from GSD version/GSD revision | GSDML V2.3 |
| Operating Mode | |
| DI | Yes |
| Supply Voltage | |
| Rated Value (DC) | 24 V |
| Permissible Range,Lower Limit (DC) | 19.2 V |
| Permissible Range,Upper Limit (DC) | 28.8 V |
| Reverse Polarity Protection | Yes |
| Input Current | |
| Current Consumption (Rated Value) | 90 mA |
| Encoder Supply |
|
| 24 V Encoder Supply | No |
| Power Loss | 1.7 W |
| Address Area | 2 byte; + 2 bytes for QI information |
| Hardware Configuration | |
| Automatic Encoding | Yes |
| Mechanical Coding Element | Yes |
| Type Of Mechanical Coding Element | Type A |
| Selection Of Baseunit For Connection Variants | |
| 1-Wire Connection | BU type A0 |
| 2-Wire Connection | BU type A0 + Potential distributor module |
| 3-Wire Connection | BU type A0 + Potential distributor module |
| 4-Wire Connection | BU type A0 + Potential distributor module |
| Digital Inputs | 550 mA |
| Number Of Digital Inputs | 16 |
| Digital Inputs, Parameterizable | Yes |
| Source/Sink Input | P-reading |
| Input characteristic curve in accordance with IEC 61131, type 3 | Yes |
| Input voltage | |
| Rated Value (DC) | 24 V |
| For Signal "0" | -30 to +5 V |
| For Signal "1" | +11 to +30V |
| Input Current | |
| For Signal "1", Typ. | 2.5 mA |
| Input Delay (For Rated Value Of Input Voltage) | |
| Parameterizable | Yes; 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms (in each case + delay of 30 to 500 μs, depending on line length) |
| Minimum at "0" to "1" | 0.05 ms |
| Maximum at "0" to "1" | 20 ms |
| Minimum at "1" to "0" | 0.05 ms |
| Maximum at "1" to "0" | 20 ms |
| Cable Length | |
| Maximum Shielded | 1 000 m |
| Maximum Unshielded | 600 m |
| Encoder |
|
| 2-Wire Sensor | Yes |
| Maximum Permissible Quiescent Current (2-wire Sensor) | 1.5 mA |
| Interrupts/Diagnostics/Status Information | |
| Diagnostics Function | Yes |
| Alarms | |
| Diagnostic Alarm | Yes |
| Diagnoses | |
| Diagnostic Information Readable | Yes |
| Monitoring The Supply Voltage | Yes |
| Parameterizable | Yes |
| Monitoring Of Encoder Power Supply | No |
| Wire-Break | Yes; Module-by-module, optional protective circuit for preventing wire-break |
| Short-Circuit | No |
| Group Error | Yes |
| Diagnostics Indication LED | |
| Monitoring Of The Supply Voltage (PWR-LED) | Yes; green PWR LED |
| Channel Status Display | Yes; green LED |
| For Channel Diagnostics | No |
| For Module Diagnostics | Yes; green/red DIAG LED |
| Potential Separation | |
| Between The Channels | No |
| Between The Channels And Backplane Bus | |
Description
Product Description
-
A digital input module is a component used in industrial automation systems to interface with digital signals
-
It converts binary signals (on/off, high/low) from field devices,such as sensors or switches,into data that a programmable logic controller (PLC) or other control systems can process
-
This module allows the control system to monitor and respond to the status of various equipment and processes in real-time
-
Warranty and support will be provided by vendor
-
Note:*Actual product image may vary from that shown on the picture
Product Specification
| Brand | Siemens |
| Product Type | Digital Input Module |
| Product Code | 6ES71316BH010BA0 |
| Product Series | Simatic ET 200SP |
| Product Type Designation | DI 16x24VDC ST |
| HW Functional Status | From FS02 |
| Firmware Version | V0.0 |
| Usable Base Units | BU type A0 |
| Product Function | |
| I&M Data | Yes; I&M0 to I&M3 |
| Isochronous Mode | No |
| Engineering With | |
| Step 7 TIA Portal Configurable/Integrated From Version | V14 |
| Step 7 Configurable/Integrated From Version | V5.5 SP3 |
| PCS 7 configurable/integrated from version | V8.1 SP1 |
| Profibus from GSD version/GSD revision | One GSD file each, Revision 3 and 5 and higher |
| Profinet from GSD version/GSD revision | GSDML V2.3 |
| Operating Mode | |
| DI | Yes |
| Supply Voltage | |
| Rated Value (DC) | 24 V |
| Permissible Range,Lower Limit (DC) | 19.2 V |
| Permissible Range,Upper Limit (DC) | 28.8 V |
| Reverse Polarity Protection | Yes |
| Input Current | |
| Current Consumption (Rated Value) | 90 mA |
| Encoder Supply |
|
| 24 V Encoder Supply | No |
| Power Loss | 1.7 W |
| Address Area | 2 byte; + 2 bytes for QI information |
| Hardware Configuration | |
| Automatic Encoding | Yes |
| Mechanical Coding Element | Yes |
| Type Of Mechanical Coding Element | Type A |
| Selection Of Baseunit For Connection Variants | |
| 1-Wire Connection | BU type A0 |
| 2-Wire Connection | BU type A0 + Potential distributor module |
| 3-Wire Connection | BU type A0 + Potential distributor module |
| 4-Wire Connection | BU type A0 + Potential distributor module |
| Digital Inputs | 550 mA |
| Number Of Digital Inputs | 16 |
| Digital Inputs, Parameterizable | Yes |
| Source/Sink Input | P-reading |
| Input characteristic curve in accordance with IEC 61131, type 3 | Yes |
| Input voltage | |
| Rated Value (DC) | 24 V |
| For Signal "0" | -30 to +5 V |
| For Signal "1" | +11 to +30V |
| Input Current | |
| For Signal "1", Typ. | 2.5 mA |
| Input Delay (For Rated Value Of Input Voltage) | |
| Parameterizable | Yes; 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms (in each case + delay of 30 to 500 μs, depending on line length) |
| Minimum at "0" to "1" | 0.05 ms |
| Maximum at "0" to "1" | 20 ms |
| Minimum at "1" to "0" | 0.05 ms |
| Maximum at "1" to "0" | 20 ms |
| Cable Length | |
| Maximum Shielded | 1 000 m |
| Maximum Unshielded | 600 m |
| Encoder |
|
| 2-Wire Sensor | Yes |
| Maximum Permissible Quiescent Current (2-wire Sensor) | 1.5 mA |
| Interrupts/Diagnostics/Status Information | |
| Diagnostics Function | Yes |
| Alarms | |
| Diagnostic Alarm | Yes |
| Diagnoses | |
| Diagnostic Information Readable | Yes |
| Monitoring The Supply Voltage | Yes |
| Parameterizable | Yes |
| Monitoring Of Encoder Power Supply | No |
| Wire-Break | Yes; Module-by-module, optional protective circuit for preventing wire-break |
| Short-Circuit | No |
| Group Error | Yes |
| Diagnostics Indication LED | |
| Monitoring Of The Supply Voltage (PWR-LED) | Yes; green PWR LED |
| Channel Status Display | Yes; green LED |
| For Channel Diagnostics | No |
| For Module Diagnostics | Yes; green/red DIAG LED |
| Potential Separation | |
| Between The Channels | No |
| Between The Channels And Backplane Bus | |
